公司新聞
冷再生機出租該如何及時發現故障？
來源：http://www.cansolv.cn/ 日期：2020-12-31
任何機器在長時間使用過后，或多或少會出現一些問題，冷再生機也不例外，但是這些問題并不會立刻展現出來，需要操作人員及時發現。
These problems will not appear immediately after the machine is cold, but it will not take long for the operator to find out.
冷再生機操作人員在工作中應注意觀察各設備的運行狀況，做好巡查工作，尤其要注意設備的傳動部位是否潤滑良好，有無磨損。此外，還應當仔細查看各連接處是否出現了松動的問題，動物是否靈活等，如果發現了問題的話，應及時進行緊固、修復或者是更換。
The operator of the cold regenerator should pay attention to observe the operation condition of the equipment, do a good job of inspection, especially pay attention to whether the transmission part of the equipment is well lubricated and whether there is wear. In addition, it is necessary to carefully check whether the joints are loose and whether the animals are flexible. If any problem is found, it should be fastened, repaired or replaced in time.
在冷再生設備運行過程中，應當注意結合眼睛、耳朵去搞清楚每一種不同的聲音，如果有不正常聲響的話，應查明原因，妥善處理。此外，還應當善于辨別各種不同的氣味。比如油溫過高，出料溫度超限，電路、電器過載而嚴重發熱，或者是短接燒壞，以及不正常摩擦而造成的過熱等，這些情況都會發出不同的氣味，這時候我們就可以及時發現問題，解決問題。
If there is a different sound in the process of regenerating, we should pay attention to the cause of each sound. In addition, we should also be good at distinguishing different odors. For example, the oil temperature is too high, the discharge temperature exceeds the limit, the circuit and electrical appliances are overloaded and seriously heated, or the short-circuit is burnt out, and the overheating is caused by abnormal friction, etc. these situations will emit different smell, at this time, we can find and solve the problem in time.
冷再生機也是一種大型路面施工機器，操作不當也會有危險，也不能順利完成工程，所以要滿足以下三點。
Cold recycling machine is also a large road construction machine, improper operation will also be dangerous, also can not successfully complete the project, so to meet the following three points.
首先要滿足的要求就是應當能夠達到較好的成品料質量。實際上，這也是筑路機械工作的一個基礎性要求。如果連這一點要求都不能滿足的話，那么就說明其不能幫助我們很好的完成工作任務。要求二就是應當具備良好的穩定性，這也是保證我們的生產工作能夠順利進行下去的一個必要條件。
The first requirement to be met is to be able to achieve better quality of finished products. In fact, this is also a basic requirement of road construction machinery. If we can't meet this requirement, it means that it can't help us to complete the task well. The second requirement is to have good stability, which is also a necessary condition to ensure the smooth progress of our production work.
第三點，就是筑路機械應該在其本身的結構方面盡可能優化設計，能夠很好的滿足用戶的操作要求。事實上，就這種設備而言，本來就非常復雜，如果不能很好的簡化操作技巧的話，那么對于用戶可能就會受到一定的影響，而且，也容易出現意外情況。
The third point is that the road construction machinery should optimize the design in its own structure as far as possible, which can well meet the operation requirements of users. In fact, as far as this kind of equipment is concerned, it is very complicated. If the operation skills can not be simplified well, the users may be affected to a certain extent, and accidents may easily occur.
以上是"冷再生機出租對冷再生機該如何及時發現故障"介紹，希望對大家有所幫助，如想了解更多資訊內容請點擊我們的網站：http://www.cansolv.cn。
The above is the introduction of "how to find the fault of the cold regenerator in time when renting the cold regenerator". I hope it can help you. For more information, please click our website: http://www.cansolv.cn 。
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：